|
In stock
|
Out of stock
|
||
|
|
|||
TinySA Ultra is a portable frequency analyzer with built-in battery, works in a wide range of 100 KHz – 6 GHz, allows you to identify and monitor the radio signals of almost any radio device.
TinySA Ultra analyzer Features
1. High sensitivity in the frequency range of 100 kHz – 800 MHz.
2. Ultra mode extends the frequency range up to 6 GHz. Can observe signals up to 12 GHz.
3. When not used as a spectrum analyzer, the unit can be used as a signal generator with a sinusoidal output signal from 0.1 to 800 MHz, or a rectangular output signal up to 4.4 GHz, or an RF test signal up to 5.3 GHz.
4. An audio headphone output allows you to listen to the demodulated signal.
5. Switches the resolution bandpass filters from 200 Hz to 850 kHz.
6. Built-in 20 dB optional LNA.
7. Color display, showing a maximum of 450 dots, provides continuous coverage up to the full frequency range.
8. MicroSD card slot for storing measurements, settings and screen shots (memory card included).
9. Input signal pitch attenuator from 0 to 31 dB (cannot be used in conjunction with the LNA).
10. Built-in calibration signal generator, which is used to automatically self-test and calibrate the (low) input signal.
11. When connected to a computer via USB, it converts to a computer-controlled spectrum analyzer or signal generator. Tinysa-APP transmits data directly to the computer. The USB interface implements the CDC protocol, and there is a large set of commands that can be used to make measurements or update internal settings. The Windows driver is installed automatically after connecting to a Windows PC. The Linux driver is built into the kernel.
12. Built-in rechargeable battery with a capacity of 3000 mAh. Charges via USB type C slot, has LED charging indicator, fully charges within 3 hours. Battery provides a minimum of 2 hours of portable use.
13. Maximum input level of +10 dBm.
14. The generator function cannot be used as a tracking generator because you cannot use the spectrum analyzer and generator functions at the same time.
Supply includes: TinySA Ultra frequency analyzer with built-in battery, USB Type-C cable, two 30 cm long ALSR100 SMA cables, SMA female to SMA female adapter, telescopic antenna, 32 GB memory card (located in the corresponding slot of the case), strap with stylus.
TinySA Ultra analyzer Specifications
Monitor: 4" TFT LCD (480×320)
Resolution filters (1,3,10 steps): 200 Hz to 850 kHz
Max low output frequency: sinus up to 800 MHz, square wave up to 4.4 GHz
Low output level: -104...-16 dBm
Input impedance: 50 ohms
Internal Low Noise Amplifier (LNA): 20 dB up to 4 GHz
Displayed points per scan: max 450
Scan time: 165 ms for 0–350 MHz
Shortest zero span time: 17 ms
DANL low input at 100 MHz: -153 dBm/Hz (LNA off) / - 169 dBm/Hz (LNA on)
DANL degrading in Ultra mode: 10 dB above 2.5 GHz; 25 dB above 5.3 GHz.
Phase noise at 10 kHz offset: -92 dBc/Hz
Phase noise at 100 kHz offset: -110 dBc/Hz
1 dB input compression level: +0.5 dBm (LNA off) / -26.5 dBm (LNA on)
Frequency stability: 1 ppm (-10...+55°C)
SD card slot: micro SD card
Audio output: 3.5mm mini jack
Battery: lithium-polymer 3.7 V, 3000 mAh
Connectors: SMA female
Interfaces: USB-CDC (Type-C), UART-TTL (2.54 mm Connector)
Overall dimensions: 117 x 72 x 23 mm / 4.6 x 2.8 x 0.9 in
Weight: 180 g / 6.3 oz